• Welcome to https://albinowners.net, the new home of Albin Owners Group!
• You will need to log in here, and you may want to bookmark this site. If you don't remember your password, use the I forgot my password link to reset it.
• All content has been transferred from our previous site.
Contact Us if you have any questions or notice a problem. If you're not receiving our email, include a phone number where we can text you.

Rubbing Strake replacement

Not model or forum specific.

Moderators: DougSea, RobS

Post Reply
User avatar
DCatSea
Gold Member
Gold Member
Posts: 918
Joined: Wed Aug 20, 2014 9:53 pm
Home Port: Alexandria VA
Location: Alexandria VA

Rubbing Strake replacement

Post by DCatSea »

One of my tasks for the layup is to replace the OEM rubbing strake on Mazboot, and trying to make it a bit sturdier than standard Albin version.
We are loving our new slip in Alexandria VA but local Washington DC boat "captains" drive as they do on the Beltway, which means regular waking of downstream marinas. Not fun.
One of the definitives for a rubbing strake is that it should be sturdy and easily replaceable when bashed around so any ideas or comments would be greatly appreciated.
Doug and Georgia
"Mazboot" - 1984 27 FC #142
Lehman 4D61
Tribe 9.5 yak
Jackson STAXX-11 yak
Alexandria City Marina - F-03
User avatar
Fred Webster
Gold Member
Gold Member
Posts: 16
Joined: Fri Jun 07, 2019 9:16 pm
Home Port: Saint John, New Brunswick, Canada
Location: New Brunswick, Canada

Re: Rubbing Strake replacement

Post by Fred Webster »

I'm following this subject, as I need to replace it, as well.
User avatar
DCatSea
Gold Member
Gold Member
Posts: 918
Joined: Wed Aug 20, 2014 9:53 pm
Home Port: Alexandria VA
Location: Alexandria VA

Re: Rubbing Strake replacement

Post by DCatSea »

Hi Fred
I'm told this goes a lot easier when the weather warms up, but/so I'll be doing it hopefully in a couple of weeks. Tried a section yesterday to check fit, and it seems very good; tight but good.
Expect it to be a SOB to fit, and will probably need a larger rubber mallet, but look forward to seeing a big difference once it's on.
I intend to put a big bead of sealer under/in the rubrail; don't think it's really needed, but just in case.....
I'll post details of the part number etc, shortly, and pics of before, during and after.
Doug and Georgia
"Mazboot" - 1984 27 FC #142
Lehman 4D61
Tribe 9.5 yak
Jackson STAXX-11 yak
Alexandria City Marina - F-03
User avatar
DCatSea
Gold Member
Gold Member
Posts: 918
Joined: Wed Aug 20, 2014 9:53 pm
Home Port: Alexandria VA
Location: Alexandria VA

Re: Rubbing Strake replacement

Post by DCatSea »

Mea Culpa
After fretting about doing this project single-handed for a while, and promising to post-pix as it progressed, I finished it and didn't get round to posting promised results.
So, my readers will be glad to know it went a lot easier than I thought it would. Following AOG advice, I left the new rail in the back of my SUV in the sun for a day or two to soften up. It did soften up.
Then I tied it up in place all round the boat. This made lifting it into position a lot easier, and single-handed installation somewhat less of a pain.
Then followed a couple of hours ladder work, lifting the rail into place and mallet-ing it over the existing backer. The bow was not easy, but it went on in one piece with some muscle power evident.
HINT: I learned quickly to use spring clamps to hold it in place until all was in place.
Transom piece is a separate section.
I screwed the ends into the aft corners with #10 1 1/4 SS screws with finishing washers.

Next stage of the operation:
All is tight, but I think there'll be some expansion by the end of the season, so during the next layup I'm going to check tightness and add screws at 24" centers on the transom, and also at the port and stbd entry points.
You do not have the required permissions to view the files attached to this post. To view images, please register for a free account.
Doug and Georgia
"Mazboot" - 1984 27 FC #142
Lehman 4D61
Tribe 9.5 yak
Jackson STAXX-11 yak
Alexandria City Marina - F-03
Post Reply

Return to “General Discussion”