per the attached picture, what I'm calling a rubber fender on the exterior of the hull, appears to have been damaged prior to my purchase. The rubber has moved upwards, and I don't know how to get it back down into place. My concern, which may be ill-founded, is water could infiltrate in this area, it's about 6" - 8" long, any thoughts as to how it can be put back into the proper position?
there is also a white caulk of some kind that was placed to seal the bottom section of the rubber to the hull along the entire rubber fender, not sure if that should be removed and replaced at some point, and if so, with what?
thanks for your time.
• Welcome to https://albinowners.net, the new home of Albin Owners Group!
• You will need to log in here, and you may want to bookmark this site. If you don't remember your password, use the I forgot my password link to reset it.
• All content has been transferred from our previous site.
• Contact Us if you have any questions or notice a problem. If you're not receiving our email, include a phone number where we can text you.
• You will need to log in here, and you may want to bookmark this site. If you don't remember your password, use the I forgot my password link to reset it.
• All content has been transferred from our previous site.
• Contact Us if you have any questions or notice a problem. If you're not receiving our email, include a phone number where we can text you.
FAQ:
• Membership information
• Burgees
• How to post photos
• Membership information
• Burgees
• How to post photos
starboard side rubber fender
Moderator: Jeremyvmd
-
gmberkley
- Gold Member
- Posts: 239
- Joined: Mon Dec 07, 2020 3:08 pm
- Home Port: Fairhaven, MA
- Location: Falmouth, MA
starboard side rubber fender
You do not have the required permissions to view the files attached to this post. To view images, please register for a free account.
Gregg M. Berkley 25 Ton Master USCG
2005 Albin 28 TE Flush Deck
Fairhaven, MA
2005 Albin 28 TE Flush Deck
Fairhaven, MA
-
Norseman
- Gold Member
- Posts: 1705
- Joined: Mon Jul 13, 2015 10:58 am
- Home Port: Palm Coast, Florida
- Location: Marina del Palma
- Contact:
Re: starboard side rubber fender
It is called a Rub Rail.
Yes, yours has been damaged, probably fasteners bent.
Need to pull the center piece to gain access, then pull the bent screws, re-bed and re-instal.
Use a moisture meter to check for any water intrusion in the hull.
Best to open up and let dry before re-installing.
Yes, yours has been damaged, probably fasteners bent.
Need to pull the center piece to gain access, then pull the bent screws, re-bed and re-instal.
Use a moisture meter to check for any water intrusion in the hull.
Best to open up and let dry before re-installing.
2001 28TE, 6LP-STE, 1,337 hrs, 19X18 four-blade wheel.
-
gmberkley
- Gold Member
- Posts: 239
- Joined: Mon Dec 07, 2020 3:08 pm
- Home Port: Fairhaven, MA
- Location: Falmouth, MA
Re: starboard side rubber fender
Your a wealth of knowledge. Thank you. Any secret as to how the rub rail is removed? There are no seams in that area as I remember and no fasteners showing.
Gregg M. Berkley 25 Ton Master USCG
2005 Albin 28 TE Flush Deck
Fairhaven, MA
2005 Albin 28 TE Flush Deck
Fairhaven, MA
-
Norseman
- Gold Member
- Posts: 1705
- Joined: Mon Jul 13, 2015 10:58 am
- Home Port: Palm Coast, Florida
- Location: Marina del Palma
- Contact:
Re: starboard side rubber fender
Thx, but I have never removed or replaced my rub rail.
Look at the center, there should be a removable strip covering up the fasteners.
Remove the strip, fix the problem and push or slide the center piece back in.
Look at the center, there should be a removable strip covering up the fasteners.
Remove the strip, fix the problem and push or slide the center piece back in.
2001 28TE, 6LP-STE, 1,337 hrs, 19X18 four-blade wheel.
-
Norseman
- Gold Member
- Posts: 1705
- Joined: Mon Jul 13, 2015 10:58 am
- Home Port: Palm Coast, Florida
- Location: Marina del Palma
- Contact:
Re: starboard side rubber fender
Probably something like this:
You do not have the required permissions to view the files attached to this post. To view images, please register for a free account.
2001 28TE, 6LP-STE, 1,337 hrs, 19X18 four-blade wheel.
-
gmberkley
- Gold Member
- Posts: 239
- Joined: Mon Dec 07, 2020 3:08 pm
- Home Port: Fairhaven, MA
- Location: Falmouth, MA
Re: starboard side rubber fender
Similar yes. The center tube on mine seems larger. Does that come out by prying it out with a screwdriver or similar and then provides access to the screws?
Gregg M. Berkley 25 Ton Master USCG
2005 Albin 28 TE Flush Deck
Fairhaven, MA
2005 Albin 28 TE Flush Deck
Fairhaven, MA
-
Norseman
- Gold Member
- Posts: 1705
- Joined: Mon Jul 13, 2015 10:58 am
- Home Port: Palm Coast, Florida
- Location: Marina del Palma
- Contact:
Re: starboard side rubber fender
Yes, I believe so, not sure.
Have done a few in the past. Some have end pieces you remove, some you pray out with a tool, perhaps even with a heat gun to make it less stiff.
If this is your first rodeo, have a boat yard do it for you, or a marine contractor specializing in stuff like this.
Pretty low tech, but easy to screw up if you are new to boats.
2001 28TE, 6LP-STE, 1,337 hrs, 19X18 four-blade wheel.
-
gmberkley
- Gold Member
- Posts: 239
- Joined: Mon Dec 07, 2020 3:08 pm
- Home Port: Fairhaven, MA
- Location: Falmouth, MA
Re: starboard side rubber fender
Not new to boats but certainly new to a lot of this. Thank you very much for the advice. I will look for someone to do this for me. Thank you again for your time and patience
Gregg M. Berkley 25 Ton Master USCG
2005 Albin 28 TE Flush Deck
Fairhaven, MA
2005 Albin 28 TE Flush Deck
Fairhaven, MA