• Welcome to https://albinowners.net, the new home of Albin Owners Group!
• You will need to log in here, and you may want to bookmark this site. If you don't remember your password, use the I forgot my password link to reset it.
• All content has been transferred from our previous site.
Contact Us if you have any questions or notice a problem. If you're not receiving our email, include a phone number where we can text you.

Low Oil Pressure Reading

Engines, Electric, Plumbing, etc.

Moderator: Jeremyvmd

Post Reply
elad

Low Oil Pressure Reading

Post by elad »

For as long as I have owned my 2000 28te, 10 yrs, the oil pressure reading has been low at low rpm. It reads just above the red zone and once warmed up will dip ever so slightly into the red. At r my above 1500 reading is well into the proper zone. I have checked with Mastry Marine and my local diesel mechanic who both say there should be no problems. So I have not concerned myself with the low readings. Still, it just does not seem right. Anyone else experiencing low oil pressure readings?
Carl
Gold Member
Gold Member
Posts: 772
Joined: Tue Feb 27, 2007 6:14 am
Home Port: Oxford, MD
Location: Preston, MD

Re: Low Oil Pressure Reading

Post by Carl »

I assume this is a Yanmar? Mine is a 2006 and since new, pressure readings at anything below 1200 RPM look to be about 15-20lbs which I too consider to be low, but was told that is normal. At cruise it looks to be around 45lbs. No problems so far and just went over 1130 hrs.
28TE "Kozy L"
"How U Albin"
carolmarie
Gold Member
Gold Member
Posts: 252
Joined: Fri Jul 23, 2010 5:54 pm
Home Port: Essex, New York

Re: Low Oil Pressure Reading

Post by carolmarie »

As Carl mentioned, assume you have a Yanmar. Very common "complaint". I have a 2001 6LP-STE and it has ALWAYS read in the red at low RPM. Early on I had the sending unit replaced (over $100) and it didn't help, so I discussed the situation with Yanmar technitions at a Newport boat show (back in 2003). Short answer - no problem so long as you don't get an annunciator alarm. Seems that the gages that Yanmar used back then were from their industrial series and those engines run mostly at higher loads (I.e. RPM) so they don't hover near the red markings. Yanmar's solution to the many expressed concerns was - now don't laugh - they simply changed the red markings to blue! In fact, they sent me a new gage shortly after the boat show. It' still in my miscellaneous parts box. I never installed it.......
Don.
User avatar
rcwhite
Gold Member
Gold Member
Posts: 163
Joined: Mon Jul 28, 2008 7:05 am
Home Port: Southport Maine

Re: Low Oil Pressure Reading

Post by rcwhite »

From the YANMAR service manual
When testing with a mechanical guage at the engine.
Oil Pressure at normal engine temp.
@ 800 RPM: 0.3 kgf/cm2, 0.03 MPa or more (4.26 psi)
@ 3800 RPM 4.5 kgf/cm2, 0.44 MPa (64 psi)

Given the wide range on the dash guage, the low side would barely register.
This was one of the first things I looked into on our 28 as it was
disturbing to look up at the guage even though it never read that low:)
I was planning on changing it to more closely match the operating range
of the engine at some point just to make myself feel better.
elad

Re: Low Oil Pressure Reading

Post by elad »

Yes, my engine is a Yan Mar 6lp-ste. Glad to hear others have experienced the same low readings and that it appears not to be a problem. Sure do not like the red readings though.
User avatar
RobS
Gold Member
Gold Member
Posts: 4044
Joined: Wed Oct 03, 2007 6:20 am
Home Port: Center Moriches, NY
Contact:

Re: Low Oil Pressure Reading

Post by RobS »

Those circa 2000 Yanmar OEM gauge clusters, (type B, C, D) are terrible for a few reasons, the oil psi gauge is one of them. Here's the VDO gauges when I redid my dash giving a much clearer reading...
You do not have the required permissions to view the files attached to this post. To view images, please register for a free account.
Rob S.
"TENACIOUS"
1974 Chris Craft 36' Commander Tournament
Cummins 6BTA 330B's

(Former Owner)
"TOY-RIFIC" 2000 28TE, 6LP, Hull 408

Luck is the residue of good design.
Maye Marie
Gold Member
Gold Member
Posts: 110
Joined: Sun May 21, 2006 10:15 pm
Home Port: Mystic River Marina Mystic Ct. Slipped
Location: Tolland Connecticut

Re: Low Oil Pressure Reading

Post by Maye Marie »

I have had similar experience with low pressure. Mine always showed low and then started to drop very low while pushing hard underway. I had switched out the sender unit and installed a mechanical gauge to go with it. The mechanical gauge always reads much higher than the Yanmar gauge and shows expected pressure. The electrical gauge for some reason will let you know you have pressure but does not give a good accurate PSI reading.

If you would like piece of mind you could do what I did. From auto parts get a mechanical gauge. Install a tee were the sender threads into engine. Then put the sender on one side of tee and the mechanical line on the other side. I mounted my mechanical gauge right on the stringer next to the engine and will open engine box and take a look if I am concern or to get a comparison from both.
Terry & Karen Ober
28 TE
Maye Marie
Mystic Ct.
socalmike
Gold Member
Gold Member
Posts: 152
Joined: Mon Sep 28, 2015 5:23 pm
Home Port: san diego

Re: Low Oil Pressure Reading

Post by socalmike »

Anyone have a pic of this type of set up. My oil pressure reads low as well but read perfect at the block. Thanks. Mike
Maye Marie
Gold Member
Gold Member
Posts: 110
Joined: Sun May 21, 2006 10:15 pm
Home Port: Mystic River Marina Mystic Ct. Slipped
Location: Tolland Connecticut

Re: Low Oil Pressure Reading

Post by Maye Marie »

Sorry I do not have a pick. Go to your current oil sender on the right side of the engine just below the oil filter. Remove the sender and install a tee as a bushing fitting. Then install your sender back on your tee and an oil line for the gauge on the bottom of the tee. Locate the gauge were you like for you.
Terry & Karen Ober
28 TE
Maye Marie
Mystic Ct.
Post Reply

Return to “Albin Maintenance”