Page 1 of 2
USB Chargers
Posted: Tue Sep 16, 2014 4:09 pm
by crowra
Relatively easy project. I got tired of charging our gadgets via an outlet and having wires everywhere (especially since my wife usually sits to the right of the wheel). Not to mention how inefficient it is to invert 12 volts DC to 120 AC then back to 5 volts DC. We now have port and starboard USB chargers along with a new 12-volt socket on the fly bridge.
Re: USB Chargers
Posted: Tue Sep 16, 2014 4:35 pm
by DougSea
Nice. That's been on my to-do list for a while for the very same reasons you mention. Is that the BlueSeas adapter? Do you know if it has 10w (iPad) power output?
Re: USB Chargers
Posted: Wed Sep 17, 2014 9:54 am
by crowra
Thanks Doug. Yes, I used Blue Seas. Amazon has them and they have several different kinds. The upper port (5V 1A) is 5 watts and the lower port (5V 2.1A) is 10.5 watts. You can get higher amp adapters if needed.
Re: USB Chargers
Posted: Wed Sep 17, 2014 11:10 am
by DougSea
I really should have clicked on the photo! The answers to the power were right there.
Thanks again!
Re: USB Chargers
Posted: Tue Oct 14, 2014 10:53 am
by seasalt
This looks perfect for me unless I am missing something. I have an extra 12 volt plug on the bridge that could be changed to this device.
My needs are:
iPhone 5v...1 amp
Samsung Galaxy 7" Tablet 5v...2 amp
KIndle Paperwhite 5v...1 amp
What makes me think that I am missing something is that my 110 v iPhone charger will not charge my Kindle Paperwhite although the 110v input and 5 volt 1 amp output are the same.
Re: USB Chargers
Posted: Sat Oct 18, 2014 10:45 am
by djblackwood
It should be noted that the total output of this USB adapter is 2.1A, so you can charge either a single tablet such as an iPad, or two phones, but not a tablet and a phone at the same time. Otherwise it is quite nice and easy to install.
Re: USB Chargers
Posted: Sat Oct 18, 2014 2:13 pm
by seasalt
Mine arrived yesterday from Amazon.
The proverbial 10 minute boat project it seemed at first. When I pulled the Perko two prong 12 volt plug that the new gadget was to replace, I noticed that the hole in the console is not nearly big enough. It needs to be bored out to 1 3/16" which will require a trip to the hardware store and bringing a vac to the bridge.
I have had several boats and have been fooled many times by the 10 minute boat project that takes all day.
Re: USB Chargers
Posted: Sun Oct 19, 2014 10:48 am
by RobS
Ron, why replace your standard 12 volt outlet? It would still be useful to have. Just add the USB port.
Re: USB Chargers
Posted: Sun Oct 19, 2014 2:57 pm
by seasalt
Rob,
There are two 12 volt outlets up there...one is a cigarette lighter style and the other one is a two prong Perko plug with a rubber boot. I don't have any 12 volt accessories that have a two prong plug. My hand held spotlights are the cigarette lighter type.
My plan was to replace the Perko with the Blue Sea USB charger but that got complicated because the Perko is in a 3/4" hole and the Blue Sea requires a 1 3/16" hole. It is very difficult to enlarge an existing hole without a pilot hole to keep the saw from wobbling. I put the problem out on the Trawler Forum and got lots of interesting ways of enlarging the hole to consider.
1. Use a Dremel barrel sander to enlarge the hole.
2. Make a double hole saw...a 3/4" inside a 1 3/16" on the same mandrill. One contributor said that worked for him. My trip to Home Depot a few minutes ago failed to find a 3/4" hole saw that would drop inside a 1 3/16" hole saw and fit on a mandrill. This simple yet elegant and ingenious solution may be workable but not for me today.
3. Grind it out with a drill bit grinder. I would chip the gelcoat if I did that.
4. Forget the whole thing and buy a cigarette lighter USB like this one from Walmart for $2.97. Which is what I almost did. Then I changed my mind and ordered a better one from Amazon for $11.99.
Re: USB Chargers
Posted: Sun Oct 19, 2014 6:14 pm
by Jay Knoll
Actually it isn't that hard to cut a larger hole. Buy the hole saw, drill a hole in a piece of scrap wood that you can clamp over the existing hole that you're trying to enlarge. Put your hole saw in the hole in the scrap and start your cut, as long as the scrap wood doesn't move you'll make a perfect cut. The hardest thing is centering the scrap wood over the hole.
Good luck!
Jay
Re: USB Chargers
Posted: Tue Oct 21, 2014 8:05 am
by djblackwood
Or use a step bit - specifically designed for just such a problem. A dremel with a drum sander works too, it would just take a bit of time to go from 3/4" to 1-3/16". The BlueSea USB socket will actually fit a 1-1/8" quite snugly (you may have to screw it in).
Re: USB Chargers
Posted: Tue Oct 21, 2014 9:25 am
by seasalt
I sent the Blue Sea back to Amazon yesterday. But I now think that I know what I would do next time this situation arises. There is no way for me to clamp a scrap of wood either inside or outside the existing hole. Inside is barely accessible and outside is a large expanse not close to any edge that might hold a clamp. At first I thought the best way was the double hole saw method. But I found out that the hole saws available at Home Depot would not mate up properly on a single mandrill. Specialty hole saws for just one cut are expensive. If I were dealing with these same size holes next time I would find or cut out a 3/4" wooden plug to glue or wedge into the existing hole and go from there.
Re: USB Chargers
Posted: Fri May 01, 2015 11:30 am
by catalina_mike
Having a bunch of hole saws is convenient for this for sure. What I do is extend the drill bit or use a 12" 1/4". We use these all the time for my day job. Put the smaller wood or other material you cut out on the drill just not all the way up into the larger hole saw and it will be your guide. I know its not for everyone but if your not comfortable find someone on your dock who works for beer or wine...
Re: USB Chargers
Posted: Fri May 01, 2015 12:04 pm
by Jay Knoll
salt
I know you have sent it back but in case you want to try again you could also use double sticky tape, like carpet tape, to hold the wood in place instead of clamps. If you're concerned that the tape might slip, having someone hold it in place while you drill should do the trick.
Jay
Re: USB Chargers
Posted: Tue May 05, 2015 8:48 pm
by Pasteur
Our house has these where people tend to charge their phones - kitchen, bed side, next to lounge chair, etc. I'm just about to add one to the outlet nearest the helm and will probably swap out the ones nearest the bunks, too.
http://www.homedepot.com/p/Leviton-Deco ... /205430236