I am looking for advice on a 1985 Albin aft cabin trawler with a Cummins engine that we are launching after 2 years of dry dock In Hamilton ON to it's new slip in Oakville.It ran beautiful In 2022. We changed the impeller, tested the battery, new white plumbers tape on the drain plug,bow thruster is fixed, all valves checked, tighten all clamps, will check the steering cables. Most anodes will survive one more summer, will test the anchor, oil is clean.
Mechanic is delayed 3 weeks. We want to launch next week
Can anyone make recommendations?
Thanks
Gilbert Jubinville 4169312758
• Welcome to https://albinowners.net, the new home of Albin Owners Group!
• You will need to log in here, and you may want to bookmark this site. If you don't remember your password, use the I forgot my password link to reset it.
• All content has been transferred from our previous site.
• Contact Us if you have any questions or notice a problem. If you're not receiving our email, include a phone number where we can text you.
• You will need to log in here, and you may want to bookmark this site. If you don't remember your password, use the I forgot my password link to reset it.
• All content has been transferred from our previous site.
• Contact Us if you have any questions or notice a problem. If you're not receiving our email, include a phone number where we can text you.
FAQ:
• Membership information
• Burgees
• How to post photos
• Membership information
• Burgees
• How to post photos
Introduction - 1985 Albin 34 Aft Cummins in Oakville ON
-
- Deckhand
- Posts: 6
- Joined: Sat May 18, 2024 10:09 am
- Home Port: Bronte Outer Harbor Ontario
-
- Swabby
- Posts: 1
- Joined: Sat Mar 23, 2024 12:06 pm
- Home Port: Cataumet Cape Cod
Re: Introduction - 1985 Albin 34 Aft Cummins in Oakville ON
Welcome aboard,
Is your new A 34 the motor yacht model? We have Hull #3, a 1986 A 34 aft cabin model with a flybridge. We've owned her for 15 years and had an A 27 for 10 years before that. We love the boat and have cruised from western CT to southern Maine quite comfortably. Why are you having the mechanic come? The season is so short that if you can have him do the work in the water (unless you think you have a problem). Run the engine on the hard with a garden hose before launch. We have the Cummins 210 turbo engine and it has been totally reliable, we did have a new reconditioned head installed in 2016 because of a cracked head (something seen in the mid 80's engines). The season is far too short to give up 3 weeks unless there is a good reason. Good luck and what is your Hull #?
Marcy K
A 34 1986
Paumanok
Cape Cod
Is your new A 34 the motor yacht model? We have Hull #3, a 1986 A 34 aft cabin model with a flybridge. We've owned her for 15 years and had an A 27 for 10 years before that. We love the boat and have cruised from western CT to southern Maine quite comfortably. Why are you having the mechanic come? The season is so short that if you can have him do the work in the water (unless you think you have a problem). Run the engine on the hard with a garden hose before launch. We have the Cummins 210 turbo engine and it has been totally reliable, we did have a new reconditioned head installed in 2016 because of a cracked head (something seen in the mid 80's engines). The season is far too short to give up 3 weeks unless there is a good reason. Good luck and what is your Hull #?
Marcy K
A 34 1986
Paumanok
Cape Cod
-
- Deckhand
- Posts: 6
- Joined: Sat May 18, 2024 10:09 am
- Home Port: Bronte Outer Harbor Ontario
Re: Introduction - 1985 Albin 34 Aft Cummins in Oakville ON
Marcy
We don't know if it's a motor yacht model. The hull type is a modified V power trawler
# AUL34107B685
We did not end up getting a mechanic and we did have a trouble free summer. We also saved $1100 by doing the winterizing ourselves.
Do we have to drain the block or manifold?
Thanks
Gilbert
We don't know if it's a motor yacht model. The hull type is a modified V power trawler
# AUL34107B685
We did not end up getting a mechanic and we did have a trouble free summer. We also saved $1100 by doing the winterizing ourselves.
Do we have to drain the block or manifold?
Thanks
Gilbert