• Welcome to https://albinowners.net, the new home of Albin Owners Group!
• You will need to log in here, and you may want to bookmark this site. If you don't remember your password, use the I forgot my password link to reset it.
• All content has been transferred from our previous site.
• Contact Us if you have any questions or notice a problem. If you're not receiving our email, include a phone number where we can text you.
• You will need to log in here, and you may want to bookmark this site. If you don't remember your password, use the I forgot my password link to reset it.
• All content has been transferred from our previous site.
• Contact Us if you have any questions or notice a problem. If you're not receiving our email, include a phone number where we can text you.
FAQ:
• Membership information
• Burgees
• How to post photos
• Membership information
• Burgees
• How to post photos
28 TE Boat stands
- Serenity
- In Memorium
- Posts: 598
- Joined: Mon Dec 13, 2010 12:15 pm
- Home Port: East Islip Anglers, New York
- Location: Long Island
28 TE Boat stands
This will be the first time that I will be bringing the yacht home. What size boat stands should I purchase. I am only supporting the stern with stands. Should I get 25-38, 29-46 or 33-50? I feel that the 29-46 will do the job.
Max
Serenity 98 28TE
East Islip, Long Island, New York
Serenity 98 28TE
East Islip, Long Island, New York
-
- Gold Member
- Posts: 159
- Joined: Fri Mar 25, 2011 9:06 am
- Home Port: Oakdale
- Location: Long Island South Shore
Re: 28 TE Boat stands
I am in the same "boat" as you. Blocking it on the 3rd of October, so I will let you know. The boat draws 38 inches so I think you are on the money if the keel just rests on some 2X8 s.
-
- Gold Member
- Posts: 238
- Joined: Tue Jul 25, 2006 4:04 pm
- Location: Ottawa Canada
Re: 28 TE Boat stands
While my boat (A-30FC) is slightly different than yours, I block it as follows.
I rest the aft end of the keel on double 6X6s, that is 5 1/2 inches off the ground. I block the forward end about in line with the forward sling marks using four double 6X6s and one 2X6, for a total of 23 1/2 inches. This makes the boat slightly down at the stern, just enough for cockpit drainage.
With this blocking arrangement I place a pair of yard stands near the forward end of the boat, just aft of the forward set of blocks. The pads on these yard stands are placed against the lip on the outer part of the hull. The pads turn out to be about 48" off the ground. The stands I use (which were provided by the selling dealer) have a 36" base and will extend to about 60", so they are about half extended when in place. I have two sets of shorter stands that I place midships and near the stern. All stand pairs are chained across under the boat to prevent slippage. I use three pairs because it is recommended that there be one pair for every ten feet of boat length.
If you are using just one pair of yard stands, I would recommend that you not use a pair that must be fully extended when in place.
My boat is to be hauled on 8 October and I can provide photos if needed.
I rest the aft end of the keel on double 6X6s, that is 5 1/2 inches off the ground. I block the forward end about in line with the forward sling marks using four double 6X6s and one 2X6, for a total of 23 1/2 inches. This makes the boat slightly down at the stern, just enough for cockpit drainage.
With this blocking arrangement I place a pair of yard stands near the forward end of the boat, just aft of the forward set of blocks. The pads on these yard stands are placed against the lip on the outer part of the hull. The pads turn out to be about 48" off the ground. The stands I use (which were provided by the selling dealer) have a 36" base and will extend to about 60", so they are about half extended when in place. I have two sets of shorter stands that I place midships and near the stern. All stand pairs are chained across under the boat to prevent slippage. I use three pairs because it is recommended that there be one pair for every ten feet of boat length.
If you are using just one pair of yard stands, I would recommend that you not use a pair that must be fully extended when in place.
My boat is to be hauled on 8 October and I can provide photos if needed.
John Murray...Albin 30FC..."katie G"...Ottawa Canada
- Pitou
- Gold Member
- Posts: 2091
- Joined: Thu Feb 22, 2007 1:34 pm
- Home Port: Gloucester, MA
- Location: Essex, MA
Re: 28 TE Boat stands
Just got around to measuring my Brownell stands:
Rear stands: 33 - 50, but the 29 - 46 will be fine. Fronts: SailboatStands 35 -52
As stated run chain between them.
Blocking: 4 inch block under the keel and the bow is blocked 33 1/2" high in order to let the standing water beneath the dinette run out the transom plug.
I provide the stands and the yard sets them and does the blocking. I figured at $ 50 each to rent them I might as well own them. The yard provides blocks at no charge. They do set a piece of 6 in wide 5/4 decking in the chine for better weight distribution.
Rear stands: 33 - 50, but the 29 - 46 will be fine. Fronts: SailboatStands 35 -52
As stated run chain between them.
Blocking: 4 inch block under the keel and the bow is blocked 33 1/2" high in order to let the standing water beneath the dinette run out the transom plug.
I provide the stands and the yard sets them and does the blocking. I figured at $ 50 each to rent them I might as well own them. The yard provides blocks at no charge. They do set a piece of 6 in wide 5/4 decking in the chine for better weight distribution.
You do not have the required permissions to view the files attached to this post. To view images, please register for a free account.
kevinS
>><<>>;>
Former Boats:
- 2006 31TE / Hull# 221
Cummins QSC 8.3 / 500 hp
December '13 - April '23
- 2002 / 28TE / Hull# 614
Cummins 6BTA 370 hp / Alaskan Bulkhead
April '04 ~ May '13
>><<>>;>
Former Boats:
- 2006 31TE / Hull# 221
Cummins QSC 8.3 / 500 hp
December '13 - April '23
- 2002 / 28TE / Hull# 614
Cummins 6BTA 370 hp / Alaskan Bulkhead
April '04 ~ May '13
- Serenity
- In Memorium
- Posts: 598
- Joined: Mon Dec 13, 2010 12:15 pm
- Home Port: East Islip Anglers, New York
- Location: Long Island
Re: 28 TE Boat stands
From what I see you are using 4 angle stands. I was going to go with 2 vertical in the stern and 2 sailboats forward. Is there any weight distribution benefit with using a vertical or angle stand in the stern? Thanks for the pictures.Pitou wrote:Just got around to measuring my Brownell stands:
Rear stands: 33 - 50, but the 29 - 46 will be fine. Fronts: SailboatStands 35 -52
As stated run chain between them.
Blocking: 4 inch block under the keel and the bow is blocked 33 1/2" high in order to let the standing water beneath the dinette run out the transom plug.
I provide the stands and the yard sets them and does the blocking. I figured at $ 50 each to rent them I might as well own them. The yard provides blocks at no charge. They do set a piece of 6 in wide 5/4 decking in the chine for better weight distribution.
Max
Serenity 98 28TE
East Islip, Long Island, New York
Serenity 98 28TE
East Islip, Long Island, New York
- Pitou
- Gold Member
- Posts: 2091
- Joined: Thu Feb 22, 2007 1:34 pm
- Home Port: Gloucester, MA
- Location: Essex, MA
Re: 28 TE Boat stands
Vertical Brownell in the stern Part# BBS-MB1Serenity wrote:From what I see you are using 4 angle stands. I was going to go with 2 vertical in the stern and 2 sailboats forward. Is there any weight distribution benefit with using a vertical or angle stand in the stern? Thanks for the pictures.
Sailboat Brownell Forward Part#-SB3
Some say to use 3 sets (probably safer), but I copied how Standish had her blocked when I bought her and went wiith my storage yard's recommendation.
You do not have the required permissions to view the files attached to this post. To view images, please register for a free account.
kevinS
>><<>>;>
Former Boats:
- 2006 31TE / Hull# 221
Cummins QSC 8.3 / 500 hp
December '13 - April '23
- 2002 / 28TE / Hull# 614
Cummins 6BTA 370 hp / Alaskan Bulkhead
April '04 ~ May '13
>><<>>;>
Former Boats:
- 2006 31TE / Hull# 221
Cummins QSC 8.3 / 500 hp
December '13 - April '23
- 2002 / 28TE / Hull# 614
Cummins 6BTA 370 hp / Alaskan Bulkhead
April '04 ~ May '13
- Serenity
- In Memorium
- Posts: 598
- Joined: Mon Dec 13, 2010 12:15 pm
- Home Port: East Islip Anglers, New York
- Location: Long Island
Re: 28 TE Boat stands
Great, that works for mePitou wrote:Vertical Brownell in the stern Part# BBS-MB1Serenity wrote:From what I see you are using 4 angle stands. I was going to go with 2 vertical in the stern and 2 sailboats forward. Is there any weight distribution benefit with using a vertical or angle stand in the stern? Thanks for the pictures.
Sailboat Brownell Forward Part#-SB3
Some say to use 3 sets (probably safer), but I copied how Standish had her blocked when I bought her and went wiith my storage yard's recommendation.
Max
Serenity 98 28TE
East Islip, Long Island, New York
Serenity 98 28TE
East Islip, Long Island, New York
- RobS
- Gold Member
- Posts: 4044
- Joined: Wed Oct 03, 2007 6:20 am
- Home Port: Center Moriches, NY
- Contact:
Re: 28 TE Boat stands
I go with 5, but that's just me.Pitou wrote:...Some say to use 3 sets (probably safer)...
Truthfully, I don't, this was just intentional overkill for Irene..
You do not have the required permissions to view the files attached to this post. To view images, please register for a free account.
Rob S.
"TENACIOUS"
1974 Chris Craft 36' Commander Tournament
Cummins 6BTA 330B's
(Former Owner)
"TOY-RIFIC" 2000 28TE, 6LP, Hull 408
Luck is the residue of good design.
"TENACIOUS"
1974 Chris Craft 36' Commander Tournament
Cummins 6BTA 330B's
(Former Owner)
"TOY-RIFIC" 2000 28TE, 6LP, Hull 408
Luck is the residue of good design.
- Pitou
- Gold Member
- Posts: 2091
- Joined: Thu Feb 22, 2007 1:34 pm
- Home Port: Gloucester, MA
- Location: Essex, MA
Re: 28 TE Boat stands
Rob, you slacker ... what no auger anchors & straps?RobS wrote:I go with 5, but that's just me.Pitou wrote:...Some say to use 3 sets (probably safer)...
Truthfully, I don't, this was just intentional overkill for Irene..
kevinS
>><<>>;>
Former Boats:
- 2006 31TE / Hull# 221
Cummins QSC 8.3 / 500 hp
December '13 - April '23
- 2002 / 28TE / Hull# 614
Cummins 6BTA 370 hp / Alaskan Bulkhead
April '04 ~ May '13
>><<>>;>
Former Boats:
- 2006 31TE / Hull# 221
Cummins QSC 8.3 / 500 hp
December '13 - April '23
- 2002 / 28TE / Hull# 614
Cummins 6BTA 370 hp / Alaskan Bulkhead
April '04 ~ May '13